A few weeks ago I was sitting in a small workshop that was mostly empty and working on the final design of a tiny home.
I was on a mission to build the perfect home.
A project I’ve been working on for over a year and a half.
I am so happy with the result of this project, but there is one thing I still want to add.
I want to expand on this project and build a new one.
There is one very important thing I want you to know about my tiny home: I’m still a complete novice.
This tiny home is based on a very basic design.
I can barely walk around with it in my hand, and it is not as sturdy as it should be.
My main goal is to create a home that can be built using very basic materials and materials that are easy to build.
If you want to learn how to build an apartment, a home, or a small house, I encourage you to check out my guide.
My next steps are to make a better prototype of this tiny house, and I also plan to learn more about how to make small houses.
The first step is to design a prototype of my tiny house.
If I’m not careful, I might make a mistake and fall short.
This is where I need your help.
First of all, I need to build my tinyhouse.
I have two goals: first, I want my tinyhome to look good, and second, I also want to build it quickly.
I will use this space to show you how to create and build your very own tiny house in a few minutes.
Once I finish my tiny build, I will share my design on the Crypto Coins forum.
It will be available for you to see and vote on!
I want all of you to get involved!
It is important that you make this project a success, because I need it to grow and I want it to reach the world.
If we reach this goal, we will have a working prototype of the home built and ready to show off.
The Tiny Home Project This tiny house is based off of a simple, yet highly efficient, construction method.
I started building this tiny home by creating a few basic plans.
The basic plans consist of one main structure: a shed with a floor that is approximately 20 inches deep.
The shed is then attached to the main structure by a simple ladder and two walls.
The main structure is a very simple structure that I use for most of my projects.
My goal with this tiny structure is to make it easy to install, so I built it using a simple but effective method of building.
I had to build this structure from scratch to create the first version of the tiny house and the basic structure.
I’m going to show how I built the tiny home in just a few seconds.
I’ll show you the basic design and how it works.
I used this simple method to make the main house.
The building of the main building I used was very simple.
I only had to make four basic sections, two to be precise: the roof and the sides of the shed.
The roof section was made from four different materials: plywood, 1/4″ plywood boards, and sheet metal.
The sides of this shed are made from a 3/8″x3/8×1/2″ sheet of plywood.
I then drilled a hole through each of these four sections of ply wood and drilled a 6-inch hole in each of the plywood pieces.
I filled this hole with glue.
I attached the top and bottom of this structure with 4-inch screws.
I cut two pieces of 3/4×2″x1″ sheet metal and used a 3-inch screw to secure the bottom and top of each piece to the roof.
I built this structure in just over 30 minutes, but this is only a first prototype.
I would like to build more small houses in the future.
In the meantime, here is the basic construction diagram.
I added a few extra pieces of ply material to the top of the structure.
There are a few additional pieces of sheet metal in the middle of the house, but the rest of the small house will remain the same.
I made a simple staircase to the upper floors of the building.
The staircase connects the roof with the shed, and the top two floors are connected by a ladder.
The ladder is attached to a metal beam that hangs above the top floors.
I tied a rope to this rope and hung it from the ceiling.
The two walls of this house are made of a 3x3x3 piece of 1/2×3″x2″.
The bottom section is made of 2x2x2.
I drilled two holes through the top sections of this small structure.
The hole I drilled is 6 inches deep and 6 inches in diameter.
I wrapped the top part of this section in 2x4x4 sheet metal sheets and then glued the bottom part